TU Berlin

Aero EnginesDipl.-Ing. Jan Mihalyovics

Logo Fachgebiet Luftfahrtantriebe

Page Content

to Navigation

Dipl.-Ing. Jan Mihalyovics (graduate engineer)

Dipl.-Ing. Jan Mihalyovics
Lupe

Research Associate and Ph.D. Candidate

Room: F 013

Tel. +49 (0)30 314-29481
Fax +49 (0)30 314-79448



Technische Universität Berlin
Department of Aeronautics and Astronautics
Chair for Aero Engines
Secretary's Office F1
Marchstraße 12-14
D-10587 Berlin

Publications

  • A Comparison of Optimal, Binary Closed-Loop Active Flow Control Applied to an Annular Compressor Stator Cascade with Periodic Disturbances
    Fietzke B., Mihalyovics J., King R.Peitsch D.
    In: King R. and Peitsch D. (Eds.): Active Flow and Combustion Control 2021,
    Notes on Numerical Fluid Mechanics and Multidisciplinary Design, vol. 152, pp. 321–335, 2022.
    Springer Nature Switzerland AG.
    https://doi.org/10.1007/978-3-030-90727-3_20 .
  • Binary Repetitive Model Predictive Active Flow Control Applied to an Annular Compressor Stator Cascade with Periodic Disturbances
    Fietzke B., Mihalyovics J., King R.Peitsch D.
    ASME. Journal of Engineering for Gas Turbines and Power.
    Accepted Manuscript, GTP-21-1308.
    https://doi.org/10.1115/1.4052382 .
  • Binary Repetitive Model Predictive Active Flow Control Applied to an Annular Compressor Stator Cascade With Periodic Disturbances
    Fietzke B., King R., Mihalyovics J., Peitsch D.
    Proceedings of the ASME Turbo Expo 2021: Turbomachinery Technical Conference and Exposition.
    Volume 4: Controls, Diagnostics, and Instrumentation; Cycle Innovations.
    Virtual Online, June 7-11, 2021, GT2021-58744, V004T05A003.
    https://doi.org/10.1115/GT2021-58744 .

  • 3D Profile Design and Optimization of a Rotor for a Low Speed Axial Compressor Wind Tunnel
    Mihalyovics J., Gambel J.Peitsch D.
    Deutscher Luft- und Raumfahrtkongress 2019,
    Darmstadt, Germany, September 30 - October 02, 2019, DocumentID: 490163,
    https://doi.org/10.25967/490163 .
  • A Qualitative Comparison of Unsteady Operated Compressor Stator Cascades with Active Flow Control
    Staats M., Mihalyovics J., Peitsch D.
    In: King R. (Eds.): Active Flow and Combustion Control 2018,
    Notes on Numerical Fluid Mechanics and Multidisciplinary Design, vol. 141, pp. 91–104, 2019.
    Springer, Cham .
    https://doi.org/10.1007/978-3-319-98177-2_6 .
  • Aerodynamic and Experimental Investigations on Optimized 3D Compressor Airfoils
    Mihalyovics J., Brück C., Meyer M., Vasilopoulos I., Peitsch D.
    Proceedings of the ASME Turbo Expo 2018: Turbomachinery Technical Conference and Exposition.
    Volume 2A: Turbomachinery.
    Oslo, Norway, June 11-15, 2018, GT2018-76826, V02AT39A038.
    https://doi.org/10.1115/GT2018-76826 .
  • Experimental Investigations on Highly Loaded Compressor Airfoils with Different Active Flow Control Parameters
    Brück C., Mihalyovics J., Peitsch D.
    Global Power and Propulsion Society Forum Montreal 2018,
    Montreal, Canada, May 7-9, 2017, GPPS-2018-54,
    https://doi.org/10.5281/zenodo.1343489 .

To top

Supervised Bachelor and Master Theses

  • Development of a software for the evaluation of measurements of periodic unsteady flows by means of pneumatic probes
    master thesis, 2021.
  • Aerodynamic Modeling and Performance Analysis of Boundary Layer Ingestion Propellers
    master thesis, 2021.
  • Redesign of an annular low speed wind tunnel
    master thesis, 2020.
  • Numerical investigation of the effect of experimentally generated leading edge erosion on the two-dimensional flow in a compressor grid
    master thesis, 2020.
  • 3D profile optimization of a compressor rotor blade for an axial low speed compressor test rig
    diploma thesis, 2019.
  • 2D design calculations of a compressor profile
    bachelor thesis, 2019.
  • Concept development for the protection of highly sensitive pressure sensors in compressor test rigs
    bachelor thesis, 2018.
  • Design and validation of an additive-manufactured and evaporator-equipped combustion chamber dome for micro gas turbines
    master thesis, 2018.

Supervised Courses

  • Konstruktion von Turbomaschinen (since summer semester 2017)
  • Gas- und Dampfturbinen (since summer semester 2017)

Navigation

Quick Access

Schnellnavigation zur Seite über Nummerneingabe